Organic compound separation – distillation, extraction, TLC and paper chromatography

ChemistryOrganic ChemistryAges 16–17Virtual lab

Use with my class

Five familiar techniques in a single simulation. Distillation: heat a liquid mixture and the thermometer holds steady at the boiling point of the more volatile component, while vapor condenses in the condenser and drips into the receiving flask. Extraction: shake the separating funnel so the solute moves from the aqueous layer into the organic solvent layer according to the partition coefficient, then open the stopcock to separate the layers. Thin-layer chromatography: solvent rises up the plate and carries the colored spots at different speeds depending on their polarity, and the simulation instantly calculates the retention factor Rf. Paper chromatography: spot inks, food colorings, leaf pigments or amino acids on a pencil baseline, run a solvent, mark the front and measure each spot with a ruler to calculate Rf and identify the components. Reflux and distillation: assemble a reflux or distillation apparatus, oxidize ethanol, make an ester or dehydrate cyclohexanol, collect the product fraction at its boiling point with or without a fractionating column and test it – and see what goes wrong when the condenser water goes in at the top, the anti-bumping granules are left out or the apparatus is sealed. Metal ions: separate Fe³⁺ from Cu²⁺ or Ni²⁺ from Co²⁺ on paper in propanone–hydrochloric acid, locate the spots with potassium hexacyanoferrate(II) or ammonia vapor and calculate each Rf.

Lesson: Separation and purification methods for organic compounds: distillation, extraction, crystallization, chromatography

What it shows

Every separation method exploits one physical difference between the components of a mixture. Distillation separates miscible liquids by boiling point; a fractionating column is needed when boiling points are close, and the ethanol–water azeotrope limits purity. Heating under reflux keeps a slow reaction boiling without losing volatile substances, after which the product is distilled off and identified. Liquid–liquid extraction relies on a solute's partition coefficient between two immiscible solvents. Chromatography separates substances – dyes, amino acids or metal ions – by how strongly the stationary phase holds them, and Rf, measured from the baseline, identifies each one against references in the same solvent.

How to use

Pick a Method, then press Run. In Distillation, watch where the thermometer levels off; in Extraction, compare hexane with ethyl acetate. In Paper chromatography, press Pause to mark the solvent front and tap each spot to record its Rf; metal ions need propanone–HCl and a locating reagent. In Reflux & distil, choose a reaction and a set-up, tick the apparatus checks and heat; press Collect in B when the thermometer reaches the product's boiling point, then Test product. Try water in at the top or no granules.

Parameters you can change

  • Method Simple distillation, Liquid–liquid extraction, Thin-layer chromatography, Paper chromatography, Reflux and distillation from a reaction
  • Mixture Ethanol + water, Hexane + toluene, Iodine dissolved in water, Leaf pigments (chlorophyll, carotene)
  • Solvent Hexane (nonpolar), Ethyl acetate (moderately polar), Ethanol (strongly polar)
  • Animation speed 0.5–3 ×
  • Samples spotted on the paper Felt-tip pen inks, Food colorings, Leaf pigments (sun and shade leaves), Amino acids (located with ninhydrin), Metal ions Fe³⁺ and Cu²⁺ (located with K₄[Fe(CN)₆] or ammonia), Metal ions Ni²⁺ and Co²⁺ (located with K₄[Fe(CN)₆] or ammonia)
  • Paper chromatography solvent Water, Ethanol, Petroleum ether + propanone (9 : 1), Butan-1-ol + ethanoic acid + water (4 : 1 : 5), Propanone + conc. HCl + water (87 : 8 : 5)
  • Reaction (reflux mode) Oxidation of ethanol (acidified dichromate), Esterification: 3-methylbutyl ethanoate (banana flavor), Dehydration of cyclohexanol to cyclohexene
  • Starting set-up (reflux mode) Heating under reflux, Distilling the product as it forms
  • Fractionating column (reflux mode)

Questions to explore

  1. Which method would you choose to remove iodine from water, and which solvent transfers the largest share of it?
  2. Why do leaf pigments separate into several spots on the TLC plate, and which pigment travels farthest?
  3. Why is the baseline drawn in pencil and above the solvent level, and how is Rf calculated from it?

Teaching ideas

All guides