Water analysis – pH, dissolved solids and distillation

Integrated ScienceMatter & MaterialsAges 11–12Virtual lab

Use with my class

Analyse tap water, sea water, rain water, river water and an unknown sample as in the school practical: measure the pH with universal indicator or a pH meter, filter off suspended solids, evaporate a known volume in a weighed basin to calculate the mass of dissolved solids (g/dm³) step by step, then distil the sample and test the distillate: pH ≈ 7, boils at 100 °C, leaves no residue. Set up the thermometer or the cooling water wrongly to see what goes wrong. The Treatment works screen runs sedimentation, sand filtration, activated carbon and chlorination (Cl₂ + H₂O ⇌ HCl + HClO, or sodium chlorate(I) bleach), with a graph of chlorine dose against surviving bacteria and by-products. The Tests for water screen uses anhydrous copper(II) sulfate, cobalt(II) chloride paper and boiling and melting points to test for water and its purity. The Desalination screen makes fresh water from sea water (about 35 g/dm³ of salts) with a solar still, a lab distillation or reverse osmosis: measure the salinity of the product with a conductivity meter, the yield in L per m² per day or cm³ per kJ, and the energy per m³. Reverse osmosis gives fresh water only above the osmotic pressure of sea water (about 2.7 MPa).

Lesson: Analysis and purification of water samples by distillation

What it shows

Natural water is a mixture: it contains dissolved salts and gases, and sometimes insoluble solids. Evaporating a known volume shows how much is dissolved, and distillation leaves the solids behind, so the distillate is pure: pH 7, boiling point 100 °C, no residue. A treatment works makes river water potable: sedimentation and sand filtration remove solids, activated carbon removes tastes and odours, and chlorine kills bacteria. Chlorine reacts with water to form chloric(I) acid, HClO; too little leaves bacteria alive, too much forms harmful by-products. Anhydrous copper(II) sulfate and cobalt(II) chloride show that water is present; boiling and melting points show whether it is pure. Desalination removes the salt: distillation evaporates the water, which takes about 2.26 kJ per gram, while reverse osmosis pushes water through a membrane at a pressure above the osmotic pressure and uses far less energy.

How to use

Pick a screen with the tabs. Analyse a sample: choose the Sample, Volume evaporated, pH by and Balance, then follow the numbered buttons or press Auto run. Treatment works: change the Raw water, Settling time, Sand filter, Activated carbon, Disinfectant, Chlorine dose, Contact time and Water pH, read the verdict and press Record result. Tests for water: choose a Liquid and run each test. On Desalination, choose the Method and Feed water salinity, set the method's controls and press Start; each run adds a row to the table.

Parameters you can change

  • Water sample Tap water, Sea water, Rain water, River water (muddy), Unknown sample (random)
  • Volume of sample evaporated 10–100 cm³
  • Filter the sample before evaporating
  • pH method Universal indicator, pH meter
  • Balance resolution 0.01 g, 0.001 g
  • Distillation set-up Correct, Wrong: thermometer bulb in the liquid, Wrong: cooling water in at the top
  • Screen Analyse a water sample, Water treatment works, Tests for water and purity, Desalination of sea water
  • Method Solar still, Lab distillation, Reverse osmosis
  • Feed water salinity 1–45 g/dm³
  • Sunlight per day 2–8 kWh/m²
  • Water depth in the tray 1–10 cm
  • Black tray
  • Heater power 100–500 W
  • Insulate the flask
  • Applied pressure 0–8 MPa
  • Recovery 10–60 %
  • Energy recovery device

Questions to explore

  1. Why does filtering lower the mass of residue from river water but not from sea water?
  2. Why does too high a chlorine dose make drinking water less safe, not more?
  3. Which results show that a liquid contains water, and which show that the water is pure?

Teaching ideas

All guides