Making a salt – copper sulfate crystals from an insoluble base and acid
Integrated ScienceChemical ReactionsAges 13–14Virtual lab
How do you mainly use this simulation?
Use it with your class: students open it from a link or a QR code, with no account needed.
Carry out the soluble-salt preparation step by step: warm dilute acid (H₂SO₄ or HCl), add an insoluble base (CuO, CuCO₃ with fizzing, or ZnO) one spatula at a time until it is in excess, filter off the excess, heat the filtrate to the point of crystallisation (tested with a cold glass rod), cool slowly or quickly, then dry and weigh the crystals. A solubility graph shows why crystals form on cooling, and a step-by-step calculation gives the theoretical yield from the moles of acid, the percentage yield and where the losses went – including the mistake of evaporating to dryness. Other tabs add the titration method for acid + alkali (find the end-point with an indicator, repeat without it, crystallise), the precipitation method for insoluble salts (mix, filter, wash, dry), double salts (Mohr’s salt, potash alum, potassium trioxalatoferrate(III)) and a solubility-rules quiz for choosing the method.
Lesson: Preparing a soluble salt from an acid and an insoluble base
What it shows
A soluble salt can be made from a dilute acid and an excess of an insoluble base such as copper(II) oxide: the excess is filtered off, and the filtrate is concentrated and cooled until hydrated crystals form. Sodium, potassium and ammonium salts are made by titration instead: find the end-point with an indicator, then mix the same volumes without it. Insoluble salts such as barium sulfate are precipitated from two solutions, filtered, washed and dried. Double salts such as Mohr’s salt and potash alum crystallise from equimolar solutions. In every method, the theoretical yield comes from the limiting reagent.
How to use
Pick a tab. In Insoluble base + acid, warm the acid, add the base with + 1 spatula until it is in excess, then follow the numbered buttons. In Titration, add indicator, run in acid (Hold: open the tap, +1 drop) and press Record titre until two titres agree, then mix again without indicator and crystallise. In Precipitation, set the Volume of solution B, then mix, filter, wash, dry and weigh. Double salts and Choose the method work the same way.
Parameters you can change
- Dilute acid Sulfuric acid H₂SO₄, Hydrochloric acid HCl
- Insoluble base Copper(II) oxide CuO, Copper(II) carbonate CuCO₃, Zinc oxide ZnO
- Volume of acid 10–50 cm³
- Acid concentration 0.5–2 mol/dm³
- Cooling Cool slowly at room temperature, Cool quickly in an ice bath
- Evaporate the solution To the point of crystallisation (correct), To dryness (mistake)
- Method Acid + insoluble base (filter off the excess), Titration of acid + alkali, Precipitation of an insoluble salt, Double salts, Choosing the method
- Salt made by titration Sodium chloride (NaOH + HCl), Potassium nitrate (KOH + HNO₃), Potassium sulfate (KOH + H₂SO₄), Ammonium sulfate (NH₃ + H₂SO₄)
- Insoluble salt made by precipitation Barium sulfate (BaCl₂ + Na₂SO₄), Lead(II) iodide (Pb(NO₃)₂ + KI), Silver chloride (AgNO₃ + NaCl), Calcium carbonate (CaCl₂ + Na₂CO₃)
- Double salt Mohr’s salt (ammonium iron(II) sulfate), Potash alum (potassium aluminium sulfate), Potassium trioxalatoferrate(III)
Questions to explore
- Why is the base added until some is left over before the mixture is filtered?
- Why does evaporating to dryness give a lower mass than the theoretical mass of CuSO₄·5H₂O?
- How do slow cooling and cooling in an ice bath change the size of the crystals?