DC circuit construction kit – build circuits, measure current and voltage
Integrated ScienceElectricity & MagnetismAges 14–15Virtual lab
How do you mainly use this simulation?
Use it with your class: students open it from a link or a QR code, with no account needed.
A free-form circuit board with three screens. On Intro, drag wires, batteries, resistors, bulbs and switches onto the board, join their ends and split junctions to separate circuits; electrons flow faster as the current grows, bulbs glow according to their power, a two-probe voltmeter and a non-contact ammeter take readings, and a short circuit sets the wire on fire. The Lab screen lets you set each component's value, the battery's internal resistance and the wire resistance, and adds fuses, a high-voltage battery, in-circuit ammeters and voltmeters, conductivity test objects (coin, paper clip, pencil, eraser, hand), a stopwatch and a schematic view with textbook symbols. Any circuit is solved by nodal analysis, so the readings obey Ohm's law and the rules for series and parallel circuits. The Kirchhoff screen gives a fixed network of two cells and three resistors: label the branch currents and loop directions, write ΣI = 0 at a junction and ΣV = 0 around each loop, solve, and check the answers with the ammeter and voltmeter. Based on the "Circuit Construction Kit: DC" simulation by PhET Interactive Simulations, University of Colorado Boulder (CC BY 4.0); rewritten.
Lesson: Series and parallel circuits
What it shows
A virtual lab bench for the lesson on series and parallel circuits in the topic of electricity. Students build circuits from wires, batteries, resistors, bulbs and switches just as on a real lab bench, then use a voltmeter and an ammeter to verify Ohm's law and the relationships for series and parallel circuits. The Kirchhoff screen applies the junction rule (ΣI = 0) and the loop rule (ΣV = 0) to a network with two cells and two loops.
How to use
On Intro, drag components onto the board, drag one end onto another to connect them and tap a junction to cut it apart. On Lab, tap a component to set its value, and add fuses, in-circuit meters and test objects. On Kirchhoff, choose B → A or A → B for each current and Clockwise or Anticlockwise for each loop, pick + or − for every term, press Check equations, enter I₁, I₂ and I₃, then confirm them with the ammeter.
Parameters you can change
- Screen Intro, Lab, Kirchhoff's laws
- Starting circuit Empty board, Battery, switch and bulb, Two bulbs in series, Two bulbs in parallel, Resistor in series with two parallel bulbs
- View Lifelike, Schematic (textbook symbols)
- Current display Electrons, Conventional current
- Show current
- Show component values
- Show component labels
- Real bulbs, resistance rises when hot (Lab)
- Battery internal resistance (Lab) 0–10 Ω
- Wire resistance (Lab), per 10 cm 0–1 Ω
- Kirchhoff network E₂ in the right branch, E₂ in the middle branch
- EMF E₁ (Kirchhoff screen) 1–24 V
- EMF E₂ (Kirchhoff screen) 1–24 V
- Resistance R₁ (Kirchhoff screen) 1–50 Ω
- Resistance R₂ (Kirchhoff screen) 1–50 Ω
- Resistance R₃ (Kirchhoff screen) 1–50 Ω
Questions to explore
- Two identical bulbs are connected to the same battery, first in series and then in parallel. In which case do they glow brighter, and why?
- What happens to the current through the battery if an ammeter is mistakenly connected in parallel with a bulb?
- In a two-loop network, what does a negative answer for a branch current tell you about your arrow?
Common questions
What is the difference between a series and a parallel circuit?
In a series circuit the components sit one after another on a single path, while in a parallel circuit each one has its own branch between the same two points. Series components carry the same current and share the battery voltage; parallel branches have the same voltage, and their currents add up to the total current.
What is a short circuit and why is it dangerous?
A short circuit is a path of almost no resistance between the two terminals of a source, so the current bypasses the components that should limit it. By Ohm's law, I = U/R, a very small R gives a very large current, which overheats the wire and can start a fire; a fuse melts first to break the circuit.
What do Kirchhoff's laws say?
Kirchhoff's laws say that the currents at a junction sum to zero (ΣI = 0) and that the voltages around any closed loop sum to zero (ΣV = 0), with currents entering counted positive and currents leaving negative. The junction rule expresses conservation of charge, and the loop rule expresses conservation of energy.
Teaching ideas
All guides- Ohm's Law Lesson Plan with a Virtual LabAn Ohm's law lesson plan with a free virtual lab: predictions, data tables with expected values, an I–V graph, discussion answers and a circuits extension.
- Series and Parallel Circuits Lesson Plan with a Virtual LabA series and parallel circuits lesson plan with a free virtual lab: predictions, current and voltage tables with expected values, and a five-question set.