Capacitors – capacitance and capacitors in circuits
PhysicsElectricity & CircuitsAges 16–17Virtual lab
How do you mainly use this simulation?
Use it with your class: students open it from a link or a QR code, with no account needed.
Change the plate area, the plate separation and the battery voltage to see the capacitance C, charge Q and stored energy W of a parallel-plate capacitor update in real time. Disconnect the battery to see the charge stay fixed while the voltage changes with the capacitor's geometry. The second screen charges the capacitor and then switches it to discharge through a light bulb, so you can watch the current and brightness fall off exponentially. The Dielectric screen slides a slab of relative permittivity εᵣ between the plates, with an E-field probe for E = U/d and a table that compares C, Q, U, E and W with and without the slab, at constant U (battery connected) or constant Q (disconnected). The Sensors screen shows how a finger on a touch screen and a MEMS accelerometer change a capacitance that an RC timing circuit measures. The Combinations screen connects two or three capacitors in series or in parallel, shows the charge and voltage on each, and measures the equivalent capacitance with a constant-current charging test (C = I ÷ ΔU/Δt). Adapted from the "Capacitor Lab: Basics" simulation by PhET Interactive Simulations, University of Colorado Boulder (CC BY 4.0); rewritten.
Lesson: Capacitors and capacitance
What it shows
A parallel-plate capacitor stores charge Q = CU, and C = ε₀εᵣS/d depends only on its geometry and on the material between the plates; the field between them is uniform, E = U/d. With the battery connected U stays fixed; disconnected, Q stays fixed. A slab over a fraction x of the plates gives C = ε₀S/d·[(1 − x) + εᵣx]. Capacitors in series carry the same charge, so 1/C = Σ1/Cᵢ; in parallel they share one voltage, so C = ΣCᵢ. A constant current I raises U at the rate I/C. The Sensors screen times an RC charge, t = RC·ln 2. Fringing fields are ignored.
How to use
On Capacitance, change S, d and U, press Disconnect battery and change S or d again. On Light bulb, press Discharge via bulb. On Dielectric, pick a Slab material, drag the slab and move the orange probe. On Sensors, drag the finger or the proof mass. On Combinations, choose Series or Parallel and set C₁ to C₃; then pick Constant current, press Run and work out C from the U–t line.
Parameters you can change
- Screen Capacitance, Light bulb, Dielectric, Sensors, Combinations
- Area of each plate S 20–100 cm²
- Plate separation d 1–10 mm
- Battery voltage U 0–12 V
- Battery connected (Capacitance screen)
- Charging from battery (Light bulb screen; untick = discharging through the bulb)
- Show charges on plates
- Show electric field lines
- Show voltmeter
- Slab material (Dielectric screen) Air (εᵣ = 1.0006), PTFE (εᵣ ≈ 2.1), Paper (εᵣ ≈ 3.7), Glass (εᵣ ≈ 6), Pure water (εᵣ ≈ 80), Custom εᵣ
- Relative permittivity εᵣ (custom material) 1–100
- Slab pushed in x (Dielectric screen) 0–100 %
- Show E-field probe (Dielectric screen)
- Sensor (Sensors screen) Touch screen (finger), Accelerometer (MEMS)
- Finger height above the glass h 0–10 mm
- Acceleration along the axis a -4–4 g
- Connection (Combinations screen) Series, Parallel
- Number of capacitors (Combinations screen) 2–3
- Capacitance C₁ 0.5–50 µF
- Capacitance C₂ 0.5–50 µF
- Capacitance C₃ 0.5–50 µF
- Source (Combinations screen) Battery, Constant current
- Battery voltage U (Combinations screen) 0–12 V
- Charging current I 0.5–20 µA
- Show C, Q and U values (Combinations screen)
Questions to explore
- With the battery disconnected, how do U, E and W change when a glass slab is pushed fully in?
- Why is the field E the same in the air and in the slab when the slab fills the gap?
- Why do capacitors in series all carry the same charge, even when their capacitances differ?